產品簡介：

• WAW-1000B型電液伺服（鋼絞線）萬能試驗機是采用了液壓動力源驅動，電液伺服控制技術，計算機數據采集處理，可實現閉環控制及自動檢測的高精度材料試驗設備，其由試驗主機、油源（液壓動力源）、測控系統、試驗器具四部分組成，最大試驗力1000kN，試驗機準確度等級優于1級。

• WAW-1000B型電液伺服（鋼絞線）萬能試驗機是一款通用性較強的產品，可以滿足國家關于金屬拉伸試驗規定中的各項標準試驗，也可以按照其它標準實現對不同材料或產品的拉伸、壓縮、彎曲、剪切等類型的試驗，可以求取所測材料的抗拉強度、屈服強度、規定非比例延伸強度、彈性模量等性能指標，可實現等速率加荷、等速率變形、等速率位移、等速率應變等閉環控制，可以進行材料或產品的工藝合格性能驗證試驗。

• 該試驗機是六立柱、雙空間結構，上橫梁與下橫梁之間為拉伸空間,下橫梁與試臺之間為壓縮空間，試驗空間通過鏈輪和絲杠旋轉帶動下橫梁上下移動來自動調整。上下橫梁上裝有液壓控制的夾持鉗口，標準機型配有V型和平面型鉗口用于夾緊圓柱試樣和平板試樣做拉伸試驗，以及鋼絞線專用鉗口用于Φ8～Φ18mm的鋼絞線的拉伸試驗；標準機型的下橫梁底端配有上壓板，試臺上配有帶球形結構的下壓板，可直接做壓縮試驗。

• 該試驗機主機的設計考慮了擴展裝配其它夾具以完成更多試驗的可能。如：配裝螺栓夾具可做螺栓的拉伸和保載，配裝彎曲夾具可做圓棒或板材的彎曲試驗，配裝剪切夾具可做圓棒剪切強度試驗，在壓縮空間中加配抗折、剪切、劈裂、彈性模量儀等可做混凝土及水泥樣塊試驗，此外，配上鋼球、錨鏈、扣件等夾具即可完成該產品的各項試驗。

• 該試驗機及配件符合GB/T228、GB/T2611、GB/T16826標準要求。

主要技術參數：

1. 試驗機級別：1級(0.5級）

2. 抗壓最大試驗力：1000kN

3. 主機結構形式：六立柱主機結構

4. 油源柜重量（kg）：300

5. 有效測量范圍：1%-100%F·S（全量程不分檔）

6. 試驗力示值相對誤差：±1%（±0.5%）

7. 整機功率（kW）：2.2

8. 變形測量范圍：1%-100%F·S

9. 變形示值相對誤差：±1%（±0.5%）

10. 位移示值相對誤差：±1%

11. 位移測量分辨力：0.001mm

12. 應力速率控制相對誤差：±2%（±1%）

13. 位移速率控制相對誤差：±1%（±0.5%）

14. 應變速率控制調節范圍：0.00025/s-0.0025/s

15. 應變速率控制相對誤差：±2%（±1%）

16. 力、變形、位移保持控制范圍：0.3%-100%F·S

17. 力、變形、位移保持控制相對誤差：≦1%

18. 中梁升降速度（mm/min）：320

19. 壓縮面最大間距（mm）：900

20. 拉伸最大間距（mm）：900

21. 活塞行程（mm）：200

22. 圓試樣夾持直徑（mm）：Φ14-Φ45

23. 扁試樣夾持厚度（mm）：0-40

24. 鋼絞線夾持直徑（mm）：Φ8 - Φ18

25. 上下壓板尺寸（mm）：Φ225

26. 彎曲試驗支點最大距離（mm）：300

27. 主機外形尺寸（mm）：900×700×2600

28. 主機重量（kg）：2800  

29. 油源柜尺寸（mm）：800×600×1600 

Product introduction:

• WAW-1000B electro-hydraulic servo (strand) universal testing machine is a high-precision material testing equipment, which adopts hydraulic power source drive, electro-hydraulic servo control technology, computer data acquisition and processing, and can realize closed-loop control and automatic detection. It consists of four parts: test main engine, oil source (hydraulic power source), measurement and control system and testing equipment. The maximum test force is 1000 kN. The accuracy level is better than grade 1.

• WAW-1000B electro-hydraulic servo (strand) universal testing machine is a universal product, which can meet various national standards for metal tensile test. It can also carry out tensile, compressive, bending and shear tests of different materials or products according to other standards. The tensile strength, yield strength and non-specified strength of the tested materials can be obtained. Proportional elongation strength, modulus of elasticity and other performance indicators can achieve closed-loop control such as constant rate loading, constant rate deformation, constant rate displacement, constant rate strain, and can be used to verify the process qualification of materials or products.

• The test machine is a six-column, double-space structure, with tension space between the upper and lower beams, and compression space between the lower beams and the test bench. The test space is automatically adjusted by rotating the lower beams with sprockets and lead screw. The upper and lower crossbeams are equipped with hydraulic control clamps. The standard machine is equipped with V-type and plane-type clamps to clamp cylinder and flat plate samples for tensile test, and the special clamps for steel strand are used for tensile test of 8-18mm steel strand. The bottom of the lower crossbeams of the standard machine is equipped with upper pressure plate, and the lower pressure plate with spherical structure is equipped on the test bench for direct compression test.

• The design of the main engine of the test machine considers the possibility of expanding the assembly of other fixtures to complete more tests. For example, bolt fixture can be used for bolt tension and loading, bending fixture can be used for bar or plate bending test, shear fixture can be used for bar shear strength test, concrete and cement sample test can be done by adding bending, shearing, splitting and elastic modulus meter in compression space, in addition, steel ball, anchor chain, fastener and other fixtures can be used to complete the product. Item test.

• The testing machine and accessories meet the requirements of GB/T 228, GB/T 2611 and GB/T 16826 standards.

Product parameters:

1. Test Machine Level: Level 1 (Level 0.5)

2. Maximum compressive test force: 1000kN

3. Main frame structure: six-column main frame structure

4. Weight of Oil Source Cabinet (kg): 300

5. Effective measurement range: 1%-100% F.S. (full range without classification)

6. Relative error of test force indication: +1%(+0.5%)

7. Whole machine power (kW): 2.2

8. Deformation measurement range: 1%-100% F.S.

9. Relative error of deformation indication: +1%(+0.5%)

10. Relative error of displacement indication: +1%

11. Resolution of displacement measurement: 0.001 mm

12. Relative error of stress rate control: +2%(+1%)

13. Relative error of displacement rate control: +1%(+0.5%)

14. Adjustment range of strain rate control: 0.00025/s-0.0025/s

15. Relative error of strain rate control: +2%(+1%)

16. Maintaining control range of force, deformation and displacement: 0.3% - 100% F.S.

17. Relative error of force, deformation and displacement keeping control: <1%

18. Lifting speed of middle beam (mm/min): 320

19. Maximum spacing of compression surface (mm): 900

20. Maximum tension spacing (mm): 900

21. Piston stroke (mm): 200

22. Holding Diameter of Round Sample (mm): 14-45

23. Clamping thickness of flat specimen (mm): 0-40

24. Clamping diameter of strand (mm): 8-18

25. Size of upper and lower pressure plates (mm): 225

26. Maximum distance of fulcrum of bending test (mm): 300

27. Main engine dimensions (mm): 900 *700 *2600

28. Host Weight (kg): 2800

Dimensions of Oil Source Cabinet (mm): 800 x 600 x 1600

Standard accessories:

1. Special clamps for strands 2. V-shaped clamps and flat clamps for other wedge-shaped clamps

The clamping diameter is 8-18mm.

3. Electronic extensometer (YYU-15/500). 4. Bending support