該試驗機是采用了液壓動力源驅動，電液伺服控制技術，計算機數據采集處理，可實現閉環控制及自動檢測的高精度材料試驗設備，其由試驗主機、油源（液壓動力源）、測控系統、試驗器具四部分組成，試驗力300kN，試驗機準確度等級優于0.5級。

該試驗機能按照相應標準進行加荷速率設置并滿足標準加荷速率控制指標對水泥、混凝土等材料進行額定試驗力下的抗壓試驗，具有負荷、時間及試驗曲線動態顯示及及時控制功能和試驗力保持功能。

該試驗機是主機油源一體結構；適用于水泥、混凝土的抗壓試驗，配以適當?shù)膴A具和測量裝置可滿足混凝土的劈拉試驗、靜壓彈性模量試驗。

該試驗機及配件符合GB/T2611、GB/T17671、GB/T16826、GB/T50081標準要求。

主要技術參數：

1、試驗力：300kN；

2、試驗機級別：0.5級；

3、壓縮空間：180mm；

4、活塞行程：80 mm；

5、固定式上壓板尺寸：φ108mm；

6、球頭式上壓板尺寸：φ170mm；

7、立柱間有效距離：285mm；

8、下壓板尺寸：φ205mm；

9、主機外形尺寸：1060×500×1400 mm；

10、整機功率：0.75kW（油泵電機0.55 kW）；

11、整機重量：450kg

日常維護：

①每次開機前檢查有無滲漏油現象（具體部位如：油管，各個控制閥，油箱等），螺栓是否（即各個螺絲的統稱）緊固，電氣是否完好；定期檢查，保持其零部件的完整性。

②每次做完試驗均應將活塞降至初始位置并及時清掃垃圾，工作臺作防銹處理。

③預防高溫、過濕、灰塵、腐蝕性介質、水等侵蝕儀器。

④每年或累計工作2000小時后必須更換液壓油。

⑤請勿在計算機內安裝其他應用軟件，以免試驗機控制系統軟件不能正常運行；應防止計算機被病毒感染。

⑥任何時候都不能帶電拔插電源線和信號線，否則很容易損壞控制元件。

⑦在試驗過程中，請不要隨意按控制柜面板、操作盒和試驗軟件上的按鈕。

⑧試驗時，不要隨意觸碰設備和各種連接線，以免影響數據的準確性。

⑨經常檢查油箱液位的變化。

⑩定期檢查控制器的連接線是否接觸良好，如有松動，應及時緊固。

?試驗后若較長時間不用設備時，關閉設備總電源。

?本設備是精密測量設備，應做到定人定機定崗，嚴禁未經培訓的非操作人員操作。

This testing machine is a high-precision material testing equipment driven by hydraulic power source, electro-hydraulic servo control technology, computer data acquisition and processing, which can achieve closed-loop control and automatic detection. It is composed of four parts: testing host, oil source (hydraulic power source), measurement and control system, and testing instruments. The testing force is 300kN, and the accuracy level of the testing machine is better than 0.5.

The test can set the loading rate according to the corresponding standards and meet the standard loading rate control index to conduct the compression test of cement, concrete and other materials under the rated test force. It has the function of dynamic display of load, time and test curve, timely control and test force maintenance.

The testing machine is a main engine oil source integrated structure; It is applicable to the compressive test of cement and concrete, and can meet the splitting tensile test and static elastic modulus test of concrete with appropriate fixtures and measuring devices.

The testing machine and accessories meet the requirements of GB/T2611, GB/T17671, GB/T16826 and GB/T50081 standards.

Main technical parameters:

1. Test force: 300kN;

2. Test machine level: 0.5;

3. Compression space: 180mm;

4. Piston stroke: 80 mm;

5. Size of fixed upper platen: φ 108mm；

6. Dimension of ball joint type upper pressing plate: φ 170mm；

7. Effective distance between columns: 285mm;

8. Lower platen size: φ 205mm；

9. Overall dimensions of main engine: 1060×500×1400 mm；

10. Overall power: 0.75kW (oil pump motor 0.55kW);

11. Operating weight: 450kg

Routine maintenance:

① Before each startup, check whether there is oil leakage (specific parts such as oil pipes, control valves, oil tanks, etc.), whether the bolts (collectively referred to as all screws) are fastened, and whether the electrical system is in good condition; Check regularly to maintain the integrity of its parts.

② After each test, the piston shall be lowered to the initial position and the garbage shall be cleaned in time. The workbench shall be treated with rust prevention.

③ Prevent the instrument from being eroded by high temperature, excessive humidity, dust, corrosive medium, water, etc.

④ The hydraulic oil must be replaced every year or after 2000 hours of operation.

⑤ Do not install other application software in the computer to avoid that the control system software of the testing machine cannot operate normally; The computer should be protected from viruses.

⑥ Do not plug and unplug the power line and signal line with electricity at any time, otherwise the control components will be easily damaged.

⑦ During the test, please do not press the buttons on the control cabinet panel, operation box and test software.

⑧ During the test, do not touch the equipment and various connecting lines at will, so as not to affect the accuracy of the data.

⑨ Check the change of oil tank level frequently.

⑩ Regularly check whether the connecting wire of the controller is in good contact. If it is loose, it should be fastened in time.

? If the equipment is not used for a long time after the test, turn off the main power supply of the equipment.

? This equipment is a precision measuring equipment, which shall be operated by fixed personnel, fixed machines and fixed posts, and untrained non operators are strictly prohibited.