該試驗機是采用了液壓動力源驅動，采用智能測控儀表對試驗數據采集處理，其由試驗主機、油源（液壓動力源）、測控系統、試驗器具四部分組成，試驗力3000kN，試驗機準確度等級優于1級。

該試驗機可以滿足關于對磚、砼、水泥等材料的標準試驗要求，手動加荷、液晶屏幕顯示負荷、時間及試驗曲線。

該試驗機是主機油源分體結構；適用于水泥、混凝土的抗壓試驗，配以適當?shù)膴A具和測量裝置可滿足混凝土的劈拉試驗。

該試驗機及配件符合GB/T2611、GB/T3159標準要求。

主要技術參數：

1、試驗力：3000kN；

2、試驗機級別：1級；

3、試驗力示值相對誤差：±1%以內；

4、主機結構：四柱框架式；

5、壓縮空間：400mm；

6、活塞行程：200mm；

7、活塞位移速度：0-40mm/min；

8、壓板尺寸：φ300mm；

9、立柱間有效距離：440mm；

10、主機外形尺寸：720×720×1610 mm；

11、控制柜外形尺寸：600×540×1370mm；

12、整機功率：1.8kW（油泵電機1.5kW）；

13、油源柜重量：約160kg；

14、主機重量：約2700kg；

日常維護：

1.每次開機前檢查有無滲漏油現象（具體部位如：油管，各個控制閥，油箱等），螺栓是否（即各個螺絲的統稱）緊固，電氣是否完好。

2.每次做完試驗均應將活塞降至初始位置并及時清掃垃圾，工作臺作防銹處理。

3.預防高溫、過濕、灰塵、腐蝕性介質、水等侵蝕儀器。

4.每年或累計工作2000小時后必須更換液壓油。

5.任何時候不能帶電拔插電源線和信號線，否則容易損壞控制元件。

6.在試驗過程中，請不要隨意按控制柜面板、操作盒和試驗軟件上的按鈕。

7.試驗時，不要隨意觸碰設備和各種連接線，以免影響數據的準確性。

8.經常檢查油箱液位的變化。

9.定期檢查控制器的連接線是否接觸良好，如有松動，應及時緊固。

10.試驗后若較長時間不用設備時，關閉設備總電源。

11.本設備是精密測量設備，應做到定人定機定崗，嚴禁未經培訓的非操作人員操作。

The testing machine is driven by hydraulic power source, and uses intelligent measurement and control instrument to collect and process test data. It consists of four parts: test host, oil source (hydraulic power source), measurement and control system, and test instruments. The test force is 3000 kN, and the accuracy of the testing machine is better than level 1.

The tester can meet the standard test requirements for bricks, concrete, cement and other materials, and can manually load, display the load, time and test curve on the LCD screen.

The tester is a main engine oil source split structure; It is applicable to the compressive test of cement and concrete, and can meet the splitting tensile test of concrete with appropriate fixtures and measuring devices.

The testing machine and accessories meet the requirements of GB/T2611 and GB/T3159 standards.

Main technical parameters:

1. Test force: 3000kN;

2. Testing machine level: Level 1;

3. Relative error of test force indication: within ± 1%;

4. Host structure: four column frame type;

5. Compressed space: 400mm;

6. Piston stroke: 200mm;

7. Piston displacement speed: 0-40mm/min;

8. Pressing plate size: φ 300mm；

9. Effective distance between columns: 440mm;

10. Overall dimensions of host:720×720×1610 mm；

11. Overall dimension of control cabinet: 600×540×1370mm；

12. Overall power: 1.8kW (oil pump motor 1.5kW);

13. Weight of oil source cabinet: about 160kg;

14. Main engine weight: about 2700kg;

Routine maintenance:

1. Before each startup, check whether there is oil leakage (specific parts such as oil pipes, control valves, oil tanks, etc.), whether the bolts (collectively referred to as all screws) are fastened, and whether the electrical system is in good condition.

2. After each test, the piston shall be lowered to the initial position and the garbage shall be cleaned in time. The workbench shall be treated with rust prevention.

3. Prevent the instrument from being eroded by high temperature, excessive humidity, dust, corrosive medium, water, etc.

4. The hydraulic oil must be replaced every year or after 2000 hours of cumulative operation.

5. The power line and signal line shall not be plugged or unplugged with electricity at any time, otherwise the control elements may be damaged easily.

6. During the test, please do not press the buttons on the control cabinet panel, operation box and test software.

7. During the test, do not touch the equipment and various connecting wires at will, so as not to affect the accuracy of data.

8. Regularly check the change of oil tank liquid level.

9. Regularly check whether the connecting wire of the controller is in good contact. If it is loose, it should be fastened in time.

10. If the equipment is not used for a long time after the test, turn off the main power supply of the equipment.

11. This equipment is a precision measuring equipment, which shall be operated by specific personnel, specific machines and specific posts. It is strictly prohibited to operate it by untrained non operators.